欢迎来到聊城福瑞营物资有限公司网站!
公司简介 联系我们
微信扫一扫
微信扫一扫
服务热线:

服务热线:

13165401858

您现在所在的位置: 首页 > 新闻动态 > 公司动态

耐磨板厂家如何进行焊接?

所属分类:公司动态 发布时间:2021-04-14 13:30:40 来源:http://www.lcnmb500.com 浏览量:

HARDOX450耐磨板厂家是采用新型的堆焊复合技术堆焊复合而成的mn360耐磨钢板厂家性能优越,硬度高,虽然在性能上有所提高,但是在安装和焊接时给我们去额带来了一些麻烦,耐磨钢板厂家厂家的技术人员提出了一些焊接的方法,经过实验是可行的,今天450耐磨钢板厂家厂家给大家总结了一下,大家可以作为耐磨钢板厂家在焊接时的参考。

Hardox450 wear-resistant plate manufacturer is made of mn360 wear-resistant steel plate by using new surfacing composite technology. The performance of the manufacturer is superior and the hardness is high. Although the performance is improved, it brings us some troubles in the installation and welding. The technicians of wear-resistant steel plate manufacturer put forward some welding methods, which are feasible through experiments. Today, 450 wear-resistant steel plate is widely used Plate manufacturers give you a summary, you can be used as a reference for wear-resistant steel plate manufacturers in welding.

耐磨板厂家这类比较硬的耐磨管道,在切割和焊接上来说,是需要有专门的设备来进行的,对于耐磨钢厂家一般是用等离子切割机来切割,焊接用一般的设备焊接就行了,关键是焊接处要连接紧密,使陶瓷层连接紧密。

Wear resistant plate manufacturers such as relatively hard wear-resistant pipe, in terms of cutting and welding, it is necessary to have special equipment to carry out, for wear-resistant steel manufacturers generally use plasma cutting machine to cut, welding with general equipment welding on the line, the key is to connect the welding place tightly, so that the ceramic layer connected tightly.

耐磨板厂家如何进行焊接?(图1)

一种HARDOX450耐磨板厂家内壁的耐磨层采用焊接的方式加工而成,加工这种产,耐磨钢板厂家需要有专门的加工设备,具体的加工方式是将准备好的待加工管材安装在焊接设备上。把焊枪和保护气准备好,启动焊接设备。

A hardox450 wear-resistant plate factory inner wall wear-resistant layer is processed by welding, processing this kind of production, wear-resistant steel plate manufacturers need to have special processing equipment, the specific processing method is to prepare the pipe to be processed on the welding equipment. Prepare the welding gun and shielding gas and start the welding equipment.

这时工件按一定的速度旋转,焊枪同时沿加工件的轴线由里向外或由外向里运动,加工件每旋转一周焊枪沿轴线向外或向里移动一个焊道的宽度,焊道的宽度可以通过调整焊枪在轴线上的摆动幅度调整,如此循环螺旋焊接直到焊接完成。

At this time, the workpiece rotates at a certain speed, and the welding gun moves from inside to outside or from outside to inside along the axis of the workpiece at the same time. Each rotation of the workpiece, the welding gun moves one weld bead width along the axis. The width of the weld bead can be adjusted by adjusting the swing amplitude of the welding gun on the axis, so as to cycle spiral welding until the welding is completed.